The stunning new Raspberry Pi 3 Model B has landed. This third generation model maintains the same popular board format as the Raspberry Pi 2 and Raspberry Pi B+, but boasts a faster 1.2GHz 64Bit SoC, and on board WiFi and Bluetooth!
We only stock PRC made Raspberry Pi’s.
NB. It is recommended to use a 2.5A Power Supply with the Raspberry Pi 3
Back-Compatibility note: The Raspberry Pi 3 Model B has the same footprint and layout as the previous Model 2/B+ version, so will fit all Model 2/B+ items. However, the addition of a WiFi & Bluetooth Antenna has resulted in the ACT and PWR LEDs being moved to the opposite side of the SD card slot. Cases for the 2/B+ with LED light pipes will fit the new RPi 3, but the light pipes will not match up with the LEDs.
Broadcom BCM2387 chipset.
1.2GHz Quad-Core ARM Cortex-A53 (64Bit)
802.11 b/g/n Wireless LAN and Bluetooth 4.1 (Bluetooth Classic and LE)
Dual Core VideoCore IV® Multimedia Co-Processor. Provides Open GL ES 2.0, hardware-accelerated OpenVG, and 1080p30 H.264 high-profile decode.
Capable of 1Gpixel/s, 1.5Gtexel/s or 24GFLOPs with texture filtering and DMA infrastructure
Boots from Micro SD card, running a version of the Linux operating system or Windows 10 IoT
85 x 56 x 17mm
Micro USB socket 5V1, 2.5A
10/100 BaseT Ethernet socket
HDMI (rev 1.3 & 1.4)
Composite RCA (PAL and NTSC)
Audio Output 3.5mm jack
USB 4 x USB 2.0 Connector
40-pin 2.54 mm (100 mil) expansion header: 2×20 strip
Providing 27 GPIO pins as well as +3.3 V, +5 V and GND supply lines
15-pin MIPI Camera Serial Interface (CSI-2)
Display Serial Interface (DSI) 15 way flat flex cable connector with two data lanes and a clock lane
Memory Card Slot
Push/pull Micro SDIO
This is a great first stepper motor, good for small projects and experimenting with steppers. This uni-polar motor has a built in mounting plate with two mounting holes. There are only 32 step (11.25 degree) per revolution, and inside is a 1/16 reduction gear set. (Actually its 1/16.032 but for most purposes 1/16 is a…Learn More
L293D Motor Drive Shield is a monolithic integrated, high voltage, high current, 4-channel driver. Basically this means using this chip you can use DC motors and power supplies of up to 25 Volts, thats some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also…Learn More
DESCRIPTION USB 11N nano wifi dongle will get your Raspberry Pi hooked up to the internet wirelessly within seconds! The unit uses the plug and play Ralink RT5370 Chipset, which requires no set up or installation on Raspian, XBMC or OpenElec, and features an integrated micro antenna to give you clear and constant WiFi signal….Learn More
For precise motion control, GT2 belts and pulleys offer excellent precision at a great price. This pulley is meant for use with GT2 6mm wide belts only – MXL belts will slip due to the different tooth profile. This pulley has 20 teeth, and a 5mm inner bore. Two set screws can be used to…Learn More
Onboard 5v->3v regulator provides 150mA for power-hungry cards 3v level shifting means you can use this with ease on either 3v or 5v systems Uses a proper level shifting chip, not resistors: less problems, and faster read/write access Use 3 or 4 digital pins to read and write 2Gb+ of storage! Activity LED lights up…Learn More
The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the Internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. It supports up to eight simultaneous socket connections. Use the Ethernet library to write sketches that connect to…Learn More
This weight sensor (load cell) is suitable for electronic balance and other high accuracy electronic weighing devices. Specifications Rated load: 5 Kg Output: 1mv / v Temperature zero drift: 0.1% F.S Output sensitivity: ± 0.15mv / v Temperature sensitivity: 0.05% F.S Excitation voltage: 5-10VDCLearn More
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version.Learn More
The MPU-6050™ parts are the world’s first MotionTracking devices designed for the low power, low cost, and high-performance requirements of smartphones, tablets and wearable sensors. The MPU-6050 incorporates InvenSense’s MotionFusion™ and run-time calibration firmware that enables manufacturers to eliminate the costly and complex selection, qualification, and system level integration of discrete devices in motion-enabled products,…Learn More
Sensitive material of MQ-2 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensor’s conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration. MQ-2 gas sensor has high sensitity to…Learn More